發那科伺服數控系統故障維修解析

發那科伺服數控系統故障維修解析

發那科報警代碼

T WORD ERROR (T碼錯誤)

T CODE ERROR (T代碼出錯，非法T代碼)

M CODE ERROR (M代碼出錯，非法M代碼)

發那科報警代碼

SPINPLE FAULT ( 主軸故障)

SPINDLE ALARM ( 主軸報警)

SPINDLE OVERLOAD ( 主軸過載)

SPINPLE LUBE FAULT ( 主軸潤滑故障)

THE SPINDLE STAU IS ERROR (主軸狀態錯誤) 

SPINDLE ORIENTAION FALLURE (主軸定向失敗)

THE THREE SPINDLE SWITCH FAULT(主軸上的接近開關)

發那科報警代碼

AC NOT READY (交流盤未準備好)

SERVO NOT READY (伺服未準備好)

NC NOT READY(NC沒準備好)

+24V NOT READY( +24V沒準備好)

MT NOT READY(機床沒準備好)

發那科報警代碼

TURRET FAULT (轉塔故障)

TURRET LIMIT (轉塔限位)

DC24VOPEN(直流24斷開)

GRAR DRIFT (檔位漂移)

PLEASE AXIS RETURN HOME（軸未回零）

PLEASE DRUM RETURN HOME（刀庫未回零）

AIRPRESS FAILURE (氣壓故障)

AIR PRESSURE DROP (壓縮空氣壓力過低)

發那科報警代碼

UNCL TOOL FALL(松刀失敗)

CLAMP TOOL FALL(夾刀失敗)

DRUM NOT PARKED(刀庫未在原值)

TOOL DESENT OR TOOL DA REEOR (刀具數據錯誤)

PLEASE UNLOAD THE TOOL ON SPRINELK(請卸下主軸上的刀)

PLEASE LOAD TOOL ON APINDLE(請裝上主軸上的刀)

DRUM OUT TO APRONDLEIS FALL( 刀庫擺向換刀位失敗)

DRUM BACK PARK IS FALL(刀庫擺回原始位失敗)

TURRENT MOTOR1 OVERLOAD (刀庫移動電機過載)

MG OVERLOAD(刀庫過載)

MG SWING OVERLOAD( 刀庫擺動過載)

AUTO TOOL CHANGE FAULT (自動換刀失敗)

TOOL DAA OUT OF RANGE (指令刀具號超出范圍)

THE ORDER TOOL NOW IN SPINDLE（目標刀具在主軸上)

THE CENTRE COOLANT IS LOWER(刀具內冷泵液位過低)

DRUM RETURN 1# POSITION FAULT(刀 庫自動回零失敗)

發那科報警代碼

A AXIS UNCLAMP FAIL ( A軸松開失敗)

A AXIS CLAMP FAIL (A軸夾緊失敗)

X ZERO POINT NOT REACHED(X軸未回零)

Y ZERO POINT NOT REACHED(Y軸未回零)

Z ZERO POINT NOT REACHED(Z軸未回零)

4TH ZERO POINT NOT REACHED(第4軸未回零)

X AXIS OVERTRAL (X軸超限)

YAXISOVERTRNL(Y軸超限)

Z AXIS OVERTRNL (Z 軸超限)

Z AXIS NOT TAFIRST REF POSITION (Z軸未在第一參考點)

發那科報警代碼

DRUM AC FAULT (自動換刀失敗)

TOOLS UNLOCKED (刀具未鎖緊)

DRUM POSITION SWITCH ERROR (刀庫位置檢測開關故障)

DRUM NOW NOT TAPARK (刀庫未在原始位置)

IT DANGOU TO MOVE DRUM(刀庫禁動)

POT UO FAILOR POT NOTTAUP POSITION (刀套未在水平位)

POT DOWN FAIL (刀套翻下動作失敗)

發那科報警代碼

BATTERY ALARM (電池報警 )

COOL ANT MOTOR OVERLOAD (冷卻泵過載)

COUNTER SWITCH REEOR (計數開關故障)

MASTERT RANSFER OVER TEMP (主變壓器過熱)

IT IS DANGOUR TO MOVE ARM(機械手禁動)

ARM MOTOR OR ARM SWITCH FALL(機械手或機械手開關故障)

EXTERNAL EMG STOP (急停按鈕被按下)

CENTRE LUBRICATION FALL (中心潤滑故障)

THE WORK NOT CLAMPED (工件未夾緊)

發那科報警代碼

TURRENT MOTOR OVERLOAD (刀盤轉動電機過載)

CHIP CONVEYER OVERLOAD (拉屑器過載)

HARD LIMIT OR SERVO ALARM(硬限位或伺服報警)

NO LUB OIL (無潤滑油)

INDEX HEAD UNLOCKED (分度頭未鎖緊)

發那科報警代碼

LOW OIL LEVEL (油位低)

AIR PRESSURE( 氣壓不足)

COOLANT NOT READY(冷卻沒準備好)

CONVEY VERLOAD (排屑過載)

LUBE PRESSURE LOW(油霧壓力低) 

LUBE EMPTY(油霧油位低，潤滑油位低)

LUB PRESSURE LOW(潤滑壓力低)

LUB EMPTY(潤滑無油)

LUB OVERLOAD(潤滑過載)